TLD.500 Hydrogen Leak Detector
An affordable, high-sensitivity hydrogen leak detector for HVAC, refrigeration, and automotive A/C technicians. Charge the system with safe 5% H₂ / 95% N₂ tracer gas, sweep the probe, and follow the rising signal straight to the leak.
- ~25 ppmH₂ sensitivity
- ~1 secResponse time
- 1000×Smaller than bubble tests
- 6–8 hrBattery life
What Is a Hydrogen Leak Detector?
A hydrogen leak detector is a handheld instrument that senses tiny amounts of hydrogen escaping from a pressurized system. Instead of relying on soap bubbles or expensive helium equipment, the technician fills the system with a non-flammable tracer gas of 5% hydrogen and 95% nitrogen.
Hydrogen is the smallest, lightest molecule there is, so it escapes through leaks that other gases and methods miss. As the probe moves along joints, brazes, and fittings, the reading climbs as it gets closer to the source, pinpointing the exact leak location.
The TLD.500 is H2Leak's original handheld hydrogen sniffer: the same high-sensitivity core as our premium models in a streamlined, lower-cost package. It's the natural starting point for technicians and shops getting into tracer gas leak detection.
Built for the Field
- Sensitive hydrogen detection, approximately 25 ppm
- Fast response of about one second
- Safe, non-flammable 5% H₂ / 95% N₂ tracer gas
- Progressive display ramp with rising audible tone
- 3-level sensitivity for coarse scan and pinpointing
- Flexible sniffer probe reaches tight spaces
- Rechargeable, 6–8 hours of battery life
- Rugged, compact case
- Direct replacement for handheld helium leak detectors
Find the Leaks Other Methods Miss
Hydrogen tracer gas detection gives technicians helium-level sniffing performance at a fraction of the cost.
1000× more sensitive
Locates leaks roughly 1000 times smaller than soap-and-water bubble testing can reveal.
Safe, low-cost tracer gas
5/95 H₂/N₂ is non-flammable, non-toxic, non-corrosive, and stocked by industrial gas suppliers.
No-clog impact sensing
No gas is pulled into the probe, so there's no pump or filter to clog with dust or moisture.
How to Find a Leak with the TLD.500
Ideal for pinpointing leaks after a pressure decay or nitrogen standing test tells you the system leaks, but not where.
Pressurize
Charge the system with 5% H₂ / 95% N₂ to a safe pressure. Higher pressure makes small leaks easier to find.
Sweep
Move the probe tip no faster than 1–2 inches per second, within about ¼ inch of the surface.
Follow
The display ramp and tone rise as hydrogen increases. Adjust sensitivity to narrow in.
Pinpoint
The point of the highest reading is the leak location.
Verify
Repair the leak, re-pressurize, and re-test to confirm the fix holds.
Where the TLD.500 Goes to Work
One detector and one tracer gas for the most common service jobs.
HVAC Service & Installation
Recover, charge with tracer gas, locate, repair, and verify on residential and commercial systems, including leaks too small for refrigerant sniffers.
Commercial Refrigeration
Track down slow leaks on supermarket racks, walk-ins, and display cases to cut refrigerant loss and support EPA leak-rate compliance.
Automotive A/C
Find vehicle air-conditioning leaks on the lift without dye or repeat visits.
Also suited to general sealed and pressurized components. See other applications.
TLD.500 Technical Specifications
| Model | TLD.500 Hydrogen Leak Detector |
|---|---|
| Detection method | Hydrogen tracer gas, impact (non-sampling) sensor |
| Tracer gas | 5% Hydrogen / 95% Nitrogen (non-flammable) |
| Sensitivity | Approx. 25 ppm H₂ (≈ 1×10⁻⁵ cc/sec) |
| Response time | Approx. 1 second |
| Sensitivity settings | 3 levels |
| Indication | Digital display with progressive ramp plus audible signal that rises with leak rate |
| Probe | Flexible sniffer probe |
| Power | Rechargeable battery, 6–8 hours operation |
| Warranty | 30 days |
TLD.500 vs. DXH-240: Which Hydrogen Leak Detector Is Right for You?
Both use the same safe 5% H₂ / 95% N₂ tracer gas and respond in about one second. The TLD.500 is the entry-level choice; the DXH-240 is H2Leak's most sensitive handheld.
| TLD.500 | DXH-240 | |
|---|---|---|
| Positioning | Entry-level, lower cost | Premium, highest-sensitivity handheld |
| Tracer gas | 5% H₂ / 95% N₂ | 5% H₂ / 95% N₂ |
| Minimum H₂ concentration | Approx. 25 ppm | 1 ppm (range 1–1,000 ppm) |
| Leak rate sensitivity | Approx. 1×10⁻⁵ cc/sec | 1×10⁻⁵ cc/sec (≈ 0.10 oz/yr refrigerant) |
| Response time | ~1 second | ~1 second |
| Sensitivity settings | 3 levels | 4-position selector |
| Detection modes | Single mode | DETECTION (auto zero) and TRACK (manual zero) |
| Display | Digital ramp + audible tone | OLED graphic ramp + tone, battery and contamination indicators |
| Probe | Flexible sniffer probe | 30 cm shape-memory probe with LED tip light |
| Replaceable sensor & probe | No | Yes |
| Battery | Rechargeable, 6–8 hours | Rechargeable, ~8 hours, USB-C |
| Warranty | 30 days | 12 months |
Choose the TLD.500 if…
You want a proven, affordable hydrogen leak detector to replace soap bubbles or an aging helium sniffer for general HVAC/R and automotive A/C work.
Choose the DXH-240 if…
You regularly chase the smallest leaks, work in commercial refrigeration or production, or want a replaceable sensor and the 12-month warranty.
Hydrogen vs. Helium vs. Bubble Testing
Helium sniffing was the go-to method for decades, but rising helium prices and shortages have pushed shops toward hydrogen, which delivers comparable sniffing performance with far cheaper equipment and gas.
| Hydrogen (TLD.500) | Helium mass spec | Helium thermal cond. | Bubble test | |
|---|---|---|---|---|
| Equipment cost | Low | About 20× higher | Moderate | Lowest |
| Tracer gas supply | Low cost, stable | High cost, shortages | High cost, shortages | None |
| Sensitivity | High (~1×10⁻⁵ cc/sec) | Very high | Lower | ~1000× less than H₂ |
| Probe clogging | None (impact sensor) | Possible | Possible | N/A |
| Service needs | Low | High | More frequent | None |
Read our full tracer gas comparison.
Hydrogen Leak Detector FAQ
What is a hydrogen leak detector?
A hydrogen leak detector is a handheld instrument that senses very small amounts of hydrogen escaping from a pressurized system. The system is filled with a safe tracer gas of 5% hydrogen and 95% nitrogen, and the detector's probe is moved along joints and fittings. The reading rises as the probe gets closer to the leak, pinpointing its exact location.
Is 5% hydrogen / 95% nitrogen tracer gas safe?
Yes. The 5/95 hydrogen-nitrogen mixture is non-flammable, non-toxic, and non-corrosive. It is widely available from industrial gas suppliers and is the standard tracer gas for hydrogen leak detection.
How sensitive is the TLD.500 hydrogen leak detector?
The TLD.500 detects hydrogen at approximately 25 ppm, equivalent to a leak rate of roughly 1×10⁻⁵ cc/sec, with a response time of about one second. That is about 1000 times smaller than the leaks bubble testing can find.
Can a hydrogen leak detector replace a helium leak detector?
For most sniffing applications, yes. Hydrogen leak detection is comparable to helium sniffing in performance, while the tracer gas costs far less and is more readily available. Helium mass spectrometers can cost around 20 times more, and both helium methods draw a gas sample into the probe, which can clog it. The TLD.500 is an impact detector, so no gas is pulled into the instrument.
What is the TLD.500 used for?
The TLD.500 is used to pinpoint leaks in HVAC systems, commercial and grocery refrigeration, automotive air conditioning, and general sealed or pressurized components, especially after a pressure decay test shows a system is leaking but not where.
What is the difference between the TLD.500 and the DXH-240?
Both use 5% H₂ / 95% N₂ tracer gas and respond in about one second. The TLD.500 is the lower-cost entry-level model, detecting about 25 ppm hydrogen with a 30-day warranty. The DXH-240 is the more sensitive premium model, detecting down to 1 ppm, with two detection modes, a 4-position sensitivity selector, an LED light at the probe tip, a replaceable sensor and probe, USB-C charging, and a 12-month warranty.
Get the TLD.500 Hydrogen Leak Detector
H2Leak has supplied hydrogen tracer gas leak detectors to US technicians since 2007. Tell us what systems you service and we'll confirm the right detector for the job.

